Hmm, looking at this I see I was ambiguous:

 

These transmitters use balanced wires to connect to the PA. The Senheiser uses a TRS (Tip-Ring-Sleeve) type connector. And, the receiver needs power. It’s the power wire that wears out. The Sennheiser came with wall-wart transformer and a connector that slides in a slot. The original had the ancillary threaded part, which has been replaced with a less expensive, generic wall-wart that just pushes into the slot.

 

A web-search yields the name: coaxial power connector. Picture from wiki
https://upload.wikimedia.org/wikipedia/commons/thumb/7/7a/Hohlstecker_und_Hohlbuchse_5%2C5x2%2C5.jpg/350px-Hohlstecker_und_Hohlbuchse_5%2C5x2%2C5.jpg

 

Ones that have the threaded part are called “Locking Coaxial Power Connectors:

Image result for locking coaxial power connector image

 

Again, I’ve replaced both the locking power connector with a non-locking one, and the locking phone plug of the Sennheiser mic—that goes into the transmitter—with a standard mini-phone plug with no problems.

 

~erik hoffman

   Oakland, ca

 

From: Callers [mailto:callers-bounces@lists.sharedweight.net] On Behalf Of Erik Hoffman via Callers
Sent: Tuesday, September 13, 2016 12:34 AM
To: callers@lists.sharedweight.net
Subject: Re: [Callers] headset mics

 

I’ve had a number of wireless mics. Many of them come with a simple connector plug, with and additional feature that holds the plug on by screwing the wire to the receiver.

 

When they break—and they do break in a life of plug in, unplug, transport to next gig—I replace them with cheap ones from our local electronics shop (Al Lasher’s on University Ave., in Berkeley CA). You don’t need the screw on tight feature, just one with the same size connector. And I’ve used these at camps, gigs, everywhere, no problem.

 

Of course, you can pay a bit more and replace them from Sennheiser or Shure…

 

~erik hoffman

   Oakland, ca

 

From: Callers [mailto:callers-bounces@lists.sharedweight.net] On Behalf Of JillAllen via Callers
Sent: Wednesday, September 7, 2016 7:12 PM
To: Dale Wilson <dale.wilson@gmail.com>
Cc: callers@lists.sharedweight.net
Subject: Re: [Callers] headset mics

 

Dale,

 

Yes, it has a standard connector. 

 

Jill


On Sep 7, 2016, at 4:47 PM, Dale Wilson <dale.wilson@gmail.com> wrote:

Hi Jill,

Does youSennheiser headset have a non-standard connector (one that screws into the transmitter/receiver?)   It's nice that mine stays plugged in, but it was a real pain when a wire broke in the cable and I had to do major surgery rather than simply replacing it with a standard connector.

 

Dale 

 

On Wed, Sep 7, 2016 at 2:50 PM, jill allen via Callers <callers@lists.sharedweight.net> wrote:

Regarding the Sennheiser:

Headpiece:  ME3-ew
Belt pack and receiver:  ew 100 G3

I like the headpiece because it stays in place, the sound quality of the system is excellent and I have never had a problem with it in 8 -10 years.

Also, I recently purchased a "Compact Powered PA System" by the name of SRM 150.  It weighs  maybe 10 pounds, I can lift it with one finger, and the one speaker sounds great and fills a big room.

Jill


_______________________________________________
Callers mailing list
Callers@lists.sharedweight.net
http://lists.sharedweight.net/listinfo.cgi/callers-sharedweight.net



 

--

Turn Observation into Data. Turn Data into Information. Turn Information into Knowledge. Turn Knowledge into Wisdom. Turn Wisdom into Beauty. Turn Beauty into Love .